Mattel MR200 MR200 surface roughness measuring instrument surface roughness measuring instrument combines many functions in one, multiple keys can be done with the use of multiple operations, so before you use, be careful to understand the meaning of each key position to facilitate your to more quickly master the instrument is used. Monitor definitions of the keys: Start measuring key. Instruments used to start the measurement. : Power key. Key to open for daily use, it does not close the battery to retain stored information. If not used for long instrument, Xuanwu roughness, turn off the instrument side rear battery switch. : The Arrow / parameter key. In the main interface, press this key to enter the parameter display interface, the surface roughness of methods of operation, press the Enter key to exit. : Down Arrow / memory key. In the main interface, press this key to enter the memory record screen. : Left arrow / Graphics key. In the main interface, press this key to access the graphical display. : Right Arrow / Print button. In the main interface, press the button to start the printer print all measurement results. : Settings / Menu key. In the main interface, press this key to enter the main interface measurement condition setting state. Press the button for about 3 seconds to enter the main menu. : Enter Enter key. In all the interface, the surface roughness, to confirm the results of setting changes or exit the screen. Special instructions for use arrow keys up and down arrow function of the general definition of the four principles are: the need to set all interfaces to modify the uniform provisions, up and down arrows to select items for switching the left and right arrows to adjust settings for specific numbers and values , that enter the menu, modify the measurement conditions and graphical display after work, do not work in the main interface. In the main interface, these arrow keys to perform the above functions only character represents. Mattel MR200 measurement conditions set in the main interface mode, press the Set / Menu button to enter the main interface measurement condition setting state. Under the measurement condition setting screen in this state, only the measurement condition setting changes, the operation can not be measured. Press the Set / Menu button again to return to the main screen state, the measurement operation. Modify the sample length according to the (lower) arrow, select Modify project, as select sampling length, press the left (right) arrows to change the sample length value, the selected area will cycle through 0.25,0.8 and 2.5, determined, press the upper (lower ) arrows to select other items. Assessment by the length (down) arrow to select Modify evaluation length, choose the number of sampling lengths assessment contained in the length, press the left (right) turn arrow cycle 1,2,3,4,5. Filter Press (down) arrow to select Modify filters, portable roughness tester, press the left (right) arrow once cycle RC, PCRC, GAUSS, DP. Range Press (down) arrow to select Modify range, press the left (right) arrow once cycle A20, A40, A80, A160. Note: This product does not use the A160, just skip use. The main interface parameters according to the (lower) arrow to select the setting display parameters. Under this interface, the user can select the parameters to be measured in the main interface displays only select one, press the left (right) arrow to cycle through all the parameters for selection. Modify the unit of measure Press the (next) arrow to select modify units of measure, press the left (right) arrow to cycle metric and imperial. Choose Print Parameters NOTE: This feature does not use this type of products. H set value when measuring peak count RPc parameters, you need to set the H value. In the main screen, press Settings / Menu button to enter the main menu, press the (down) arrow to select input H value, press the Enter key to enter the setting interface. Press the (lower) arrow Shift, press the left (right) arrow adjusted figures. Press the Set / Menu button to exit to the main interface. C set straight when measuring the profile bearing ratio Rmr parameters, we need to set the C value. In the main screen, press Settings / Menu button to enter the main menu, press the (down) arrow to select input C value, press the Enter key to enter the setting interface. Press the Enter key line feed, according to the (lower) arrow Shift, press the left (right) arrows to adjust the numbers. Press the Set / Menu button to exit to the main interface. Surface roughness | surface roughness (certified) | roughness provided by the Beijing Xuanwu District, US Tyco Technology Limited. Beijing-US Science and Technology Co., Ltd. Tyco (www.mitech-ndt.com) is Beijing's Haidian District, a leader in electronic measuring instruments over the years, the company implement the scientific management, innovation and development, the principle of honesty and trustworthiness, and satisfy customers needs. Tyco in the US leadership with the staff warmly welcome all inquiries negotiations to create the United States Tyco better future.